Ubiquiti UniFi Access Hub 3x GbE PoE out, 1xGbE PoE++ in

A single
- door mechanism that provides complete entry and exit control via connected Access Readers.

Features

- (2) Lock terminals (12V and Dry)

- (2) AUX terminals for an external siren and automatic door opener

- (4) Additional inputs (sensors and buttons)

- Connect and power using PoE++

- Connect to two UniFi Access readers and one UniFi Protect camera or UniFi Protect Chime

Specifications
Mechanical

- Dimensions: 190 x 126 x 30.5 mm (7.5 x 5 x 1.2")

- Weight: 457 g (1 lb)

- Enclosure material: Plastic enclosure with metal mount plate

- Mounting options: DIN rail

Hardware

- Networking interface: (4) 1 GbE

- PoE interface: (3) PoE (Pins 1, 2+; 3, 6
- )

- Power method:
• PoE++
• UL 294 Power
- limited Class 2 PSU
• UL 60950
- 1/62368
- 1 LPS/PS2 PSU

- Supported voltage range: 48V DC

- Max. power consumption: 51W

- Total available PoE: 60W

- Max. PoE wattage per port: 15.4

- Voltage range PoE mode: 44–57V DC

- Input terminals
• REX: request to exit
• REN: request to enter
• REL: remote release
• DPS: door position sensor

- Dry output relay
• Lock: rated 30V DC, up to 1A
• Aux: rated 30V DC, up to 1A

- Powered output relay
• Lock: 12V DC, up to 1A
• Aux: 12V DC, up to 0.33A
• Line: 12V DC, up to 0.33A

- Button: (1) Factory reset

Recommend max. cable length
18 AWG UACC
- Cable
- DoorLock 20 AWG length 22 AWG length 24 AWG length
Relay length

UA
- Lock
- Electric (400mA) 100 m (217 ft) 42 m (328 ft) 66 m 138 ft) 25 m (82 ft)


UA
- Lock
- Magnetic
- 270kg (800mA) 46 m (151 ft) 30 m (98 ft) 20 m (66 ft) 12 m (29 ft)


UA
- Lock
- Magnetic
- 540kg (500mA) 80 m (262 ft) 51 m (167 ft) 32 m (105 ft) 20 m (66 ft)


Other locks (1A) 36 m (118 ft) 24 m (79 ft) 15 m (49 ft) 9 m (30 ft)





- Operating environment: Indoor use only

- Ambient operating temperature: 0 to 40° C (32 to 104° F)

- Ambient operating humidity: 5 to 90% noncondensing

- Software information: The software version of a product can be checked at https://unifi.ui.com

- UL 294 level:
• Destructive attack: Level I
• Line security: Level I
• Endurance: Level I
• Standby power: Level I

- UL 294 statement
• Compliance with IEEE 802.3 specifications was not verified as part of UL 294.
• The equipment is intended to comply with the section of the National Electrical Code, ANSI/NFPA 70, Article 725.121, Power Sources for Class 2 and Class 3 Circuits.

- PoE cabling requirements:
• Cable 5e cabling is the minimum performance category recommended. The performance category utilized should match the transmission speed required at the installation site.
• The minimal conductor gauge permitted to connect between the PSE or power injector and the PD shall be 26 AWG (0.13 mm 2 ) for patch cords; 24 AWG (0.21 mm 2 ) for horizontal or riser cable.

- CAN/ULC
- 60839
- 11
- 1 Grade: Grade assignment: I

- Certifications: CE, FCC, IC, UL 294, CAN/ULC
- 60839
- 11
- 1

- Document number, and issue date and/or revision level: UA
- Hub, Ver 02

LEDs

- PoE in:
• Steady white: Pending adoption
• Steady blue: Adopted
• Alternating white/blue: Firmware updating

- PoE out : Blinking white: Active signal

- Input terminals: Blinking white: Active signal

- Output relays: Blinking white: Relay triggered

Software

- Management application: UniFi Access: Version 1.22.17 and later